| The Harvestman... en MKII | |
|
+5OSICA HighKori -Lamalogik- bambou dropthedyle MechaSeb 9 participants |
Auteur | Message |
---|
MechaSeb Admin
Messages : 4363 Date d'inscription : 15/10/2010 Age : 39
 | Sujet: The Harvestman... en MKII Dim Sep 30 2012, 14:06 | |
| Après l'annonce du Tyme Sefari MKII, voilà que The Harvestman remet le couvert avec cette-fois la version 2 du Hertz-Donut. Pas beaucoup d'infos pour le moment apparemment mais déjà une image de la facade. Tyme Sefari MK2 : [Vous devez être inscrit et connecté pour voir cette image]Hertz Donut MK2 : [Vous devez être inscrit et connecté pour voir cette image] _________________ Les compilations synthé-mod Albums & EPs 100% Serge Modular
| |
|
 | |
dropthedyle Grand lama

Messages : 423 Date d'inscription : 12/09/2012 Localisation : Belle gigue
 | Sujet: Re: The Harvestman... en MKII Dim Sep 30 2012, 18:35 | |
| pour citer le gouverneur :
Changes from the original:
24bit/96khz conversion on both FM inputs and waveform outputs - a completely new hardware design. The generated sine wave probably sounds better than the output circuitry is capable of reproducing. Attenuverters on all but one of the CV inputs, with center detent and a musically useful deadband FM inputs are thru-zero nice 3-color illuminated tact switches instead of the big buttons "range" switch for each oscillator, from LFO rate, to useful audio range, and then up to 48khz. Square wave outputs and FM inputs are fixed, no secret button combos necessary Discontinuity function has clean/dirty waveshaping modes (similar to the 259e), and the "fractal" discontinuity from the original Tracking generator now has a knob and CV input. The three modes (named by the color of the mode button) are as follows: Orange is the "bad/worse" from the original, with the knob selecting the time constant. Red is an improved version of the "stupid" tracking where the modulator will successfully converge on the destination frequency. Green locks the frequency of the modulator to the primary, with the knob controlling the amount of phase offset. This knob is now also a destination on the modulation bus. skiff friendlier more expensive | |
|
 | |
MechaSeb Admin
Messages : 4363 Date d'inscription : 15/10/2010 Age : 39
 | Sujet: Re: The Harvestman... en MKII Lun Nov 05 2012, 11:51 | |
| démo vidéo du Tyme Sefari MkII
_________________ Les compilations synthé-mod Albums & EPs 100% Serge Modular
| |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Sam Jan 26 2013, 13:51 | |
| Je bump ce thread pour savoir si depuis quelqu'un a pu essayer le Tyme Sefari mkII ? (Je pense de plus en plus à craquer en tout cas  ) Et je voulais savoir ce que les possesseurs du Phonogen en pensaient. Je trouve que l'interface du Tyme Sefari est beaucoup plus clair et d'après les démos que j'ai pu écouter j'ai l'impression qu'ils ont un son assez différent. Je sais que le phonogen a un pre-amp sur son entrée audio, est ce que c'est pareil pour le Tyme Sefari ? On peut rentrer directement un signal de niveau line dedans ? | |
|
 | |
HighKori -Lamalogik- Petit lama

Messages : 28 Date d'inscription : 13/01/2013 Age : 50 Localisation : Paris
 | Sujet: Re: The Harvestman... en MKII Sam Jan 26 2013, 15:47 | |
| Alors je trouve que c'est super jolis les potards rouge et noir, moi qui n'aime pas trop la tronche des modules eurorack en général, mais alors l'ergonomie des faders, AU SECOUUUUUUUUUUUUUURRRRRRRRRrrrrr !!!!!!!! Je suppute qu'elle ne sont pas crantées ?!? Ce serrait pas mieux en verticales pour jouer dessus ??? En tout cas l'idée est super, surtout le switch de direction (et je le verrait bien en bout de ligne des faders si verticale). Et ça a l'air de bien sonner. (Merci M pour la démo...) Compatible alim Doepfer ? Une idée du prix ?? et ideme pour l'entrée nivau phono ? | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Sam Jan 26 2013, 18:02 | |
| - HighKori -Lamalogik- a écrit:
- Je suppute qu'elle ne sont pas crantées ?!?
Des faders crantés n'auraient strictement aucun sens ici... Ca rendrait le module inutilisable. - HighKori -Lamalogik- a écrit:
- Ce serrait pas mieux en verticales pour jouer dessus ???
Je ne sais pas trop, à vrai je ne me rend pas bien compte de la taille des faders. A l'horizontal ça me parait plus cohérent vu que c'est comme-ci tu voyais ta forme d'onde dans un sampler virtuel et que tu ajustais les points de loop. - HighKori -Lamalogik- a écrit:
- Compatible alim Doepfer ?
Tout les modules Eurorack sont compatibles avec une alimentation Doepfer, c'est la base du standard Eurorack. - HighKori -Lamalogik- a écrit:
- Une idée du prix ??
420 euros dans nos contrées. | |
|
 | |
HighKori -Lamalogik- Petit lama

Messages : 28 Date d'inscription : 13/01/2013 Age : 50 Localisation : Paris
 | Sujet: Re: The Harvestman... en MKII Sam Jan 26 2013, 19:35 | |
| Merci pour l'info sur l'Eurorack.
Je n'en ai qu'en desktop, donc je n'était pas sur.
Donc si je suis pas complètement planté du Bios, les X-Series de Macbeth aussi !!! Et c'est pas une bonne nouvelle pour ma CB......
En fait, je parlait surtout de la (supposé) difficulté à trouver un point très précis dans la boucle, pour des rythmes par ex. , et donc de crants sérigraphiés ( je me suis mal exprimé ) Et pour le jeux en live, personnellement, le fait d'avoir l'habitude des faders arp ou des tables de mix me pose un problème pour avoir des mouvements rapides et précis horizontalement, surtout si le module est placé dans une unité verticale. 420 euros c'est raisonnable je trouve pour ce genre d'unité ultra utile. | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Sam Jan 26 2013, 21:19 | |
| - HighKori -Lamalogik- a écrit:
- Donc si je suis pas complètement planté du Bios, les X-Series de Macbeth aussi !!!
Et c'est pas une bonne nouvelle pour ma CB...... Oui c'est ça, la version Eurorack des modules de MacBeth sont compatibles avec une alim' Doepfer. - HighKori -Lamalogik- a écrit:
- En fait, je parlait surtout de la (supposé) difficulté à trouver un point très précis dans la boucle, pour des rythmes par ex. , et donc de crants sérigraphiés ( je me suis mal exprimé )
Et pour le jeux en live, personnellement, le fait d'avoir l'habitude des faders arp ou des tables de mix me pose un problème pour avoir des mouvements rapides et précis horizontalement, surtout si le module est placé dans une unité verticale. Je vois ce que tu veux dire mais le jeu live en touchant aux faders du Tyme Sefari ça m'a l'air un peu casse gueule ! Dans la démo ça a l'air de bien glitch par moment quand même, ça fait pas très "propre" mais c'est pas vraiment le but d'un module de The Harvestman. Sinon pour avoir des points de cue programmables dans ta boucle pour du jeu live, regarde du coté du Phonogène de Make Noise, ça devrait te plaire  . - HighKori -Lamalogik- a écrit:
- 420 euros c'est raisonnable je trouve pour ce genre d'unité ultra utile.
Va dire ça à mon banquier | |
|
 | |
HighKori -Lamalogik- Petit lama

Messages : 28 Date d'inscription : 13/01/2013 Age : 50 Localisation : Paris
 | Sujet: Re: The Harvestman... en MKII Sam Jan 26 2013, 21:44 | |
| Merci bambou  pour l'info du phonogène ça à l'air po mal ce truc. En fait, pour l'instant, mes boucles, je les bosse sur de vieilles MPC(2000xl), pour le live c'est le top du top, mais je trouve l'idée du module super intéressant. Et les banquiers, je leurs parle pas, je | |
|
 | |
OSICA Maître Zen

Messages : 1035 Date d'inscription : 27/10/2011 Age : 38 Localisation : Liège - Belgique
 | Sujet: Re: The Harvestman... en MKII Dim Jan 27 2013, 18:25 | |
| | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Dim Jan 27 2013, 20:05 | |
| | |
|
 | |
OSICA Maître Zen

Messages : 1035 Date d'inscription : 27/10/2011 Age : 38 Localisation : Liège - Belgique
 | Sujet: Re: The Harvestman... en MKII Dim Jan 27 2013, 20:37 | |
| Il y a aussi le malgorihtm II [Vous devez être inscrit et connecté pour voir cette image] | |
|
 | |
OSICA Maître Zen

Messages : 1035 Date d'inscription : 27/10/2011 Age : 38 Localisation : Liège - Belgique
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 10:31 | |
| Monsieur Harvestman a été conquit par le mini ms-20, il sort deja un adaptateur CV/HZ: [Vous devez être inscrit et connecté pour voir cette image]"Many good things were displayed at NAMM. To me, one of the most important was the new Korg MS-20 Mini. I played with it for a long time and enjoyed it very much. It is very close to my full-size model. The MS-20 itself is an electronic instrument of extreme cultural importance, being the tool that motivated the development of several significant electronic music styles. This new version, available to all at a very low price, can only mean good things for the further development of these styles, and modular synthesis technique in general.
Because of this impending instrument release, I announce with great satisfaction ENGLISH TEAR, the first in a line of small utility modules. This module features the expected "voltage processor" attenuverter and big offset knobs, but also includes a full set of functions for interfacing to an MS-20. Easy conversion from exponential volt-per-octave to linear hertz-per-volt and back, as well as V-trigger to S-trigger conversion. Jack normalling fixes the voltage processors to these converter circuits, so you may scale the input voltages as desired. The log/expo converter ciruits also have many other uses in your modular system beyond the conversion of pitched voltages.
Price? Cheaper than anything else I've done. It will be released when the MS-20 comes out. I was thinking of dropping it into the Zorlon/Donut production run scheduled for April, but if the MS is somehow released before that I can expedite the build." | |
|
 | |
mercutio Maître Zen

Messages : 2748 Date d'inscription : 08/11/2010 Age : 45
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 10:58 | |
| l'adaptateur c'est pour les anciens... le nouveau est en v/oct ... | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 11:11 | |
| - mercutio a écrit:
- le nouveau est en v/oct
D'après ce que j'avais compris le clavier ne l'était pas (mais je suis peut être à coté de la plaque ?  ). | |
|
 | |
robonom Lama-mia !

Messages : 567 Date d'inscription : 28/02/2012 Localisation : Nantes L.A west coast
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 12:19 | |
| Ça serait con | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 12:57 | |
| D'après le site Korg : - Citation :
Keyboard:
Keyboard control voltage output (Exponential) (0 - +8V) Keyboard trigger output (+5V-->GND) VCO-1 + VCO-2 control voltage input (Linear response)(0 - +8V) VCO-2 control voltage input (Linear response) (0 - +8V)
VCO:
VCO-1 + VCO-2 external frequency control input (OCT/V) (-5V - +5V)
VCF:
External signal input (3Vp-p max.) External High pass filter cutoff frequency control input (2OCT/V) (-5V - +5V) External Low pass filter cutoff frequency control input (2OCT/V) (-5V - +5V) J'ai peut être pas bien compris mais c'est spécifié "Exponential" pour le VC Out du clavier et pas OCT/V, on doit donc supposé qu'il n'est pas calibré pour 1OCT/V ? Edit : Et le VCF Input en 3Vp-p max c'est dommage  . | |
|
 | |
Haddock Petit lama

Messages : 21 Date d'inscription : 14/08/2012 Age : 53 Localisation : Toulouse
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 13:57 | |
| - OSICA a écrit:
Because of this impending instrument release, I announce with great satisfaction ENGLISH TEAR, the first in a line of small utility modules. This module features the expected "voltage processor" attenuverter and big offset knobs, but also includes a full set of functions for interfacing to an MS-20. Easy conversion from exponential volt-per-octave to linear hertz-per-volt and back, as well as V-trigger to S-trigger conversion. Jack normalling fixes the voltage processors to these converter circuits, so you may scale the input voltages as desired. The log/expo converter ciruits also have many other uses in your modular system beyond the conversion of pitched voltages.
Price? Cheaper than anything else I've done. It will be released when the MS-20 comes out. I was thinking of dropping it into the Zorlon/Donut production run scheduled for April, but if the MS is somehow released before that I can expedite the build."[/i] Cela concerne donc clairement le nouveau MS-20 aussi, pas que les anciens. Logique, puisque passer en interne à du Volt/Oct aurait nécessité pas mal de re-design et que Korg affirme depuis le départ qu'à l'exception du convertisseur Midi (note-only) et du VCA (circuit avec un meilleur rapport signal/bruit que l'original), ils ont repris les plans du MS-20 à l'identique. | |
|
 | |
Yohda Lama-mia !

Messages : 756 Date d'inscription : 08/11/2010
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 14:55 | |
| Oui, mais il me semble avoir lu que le clavier sortait en expo, de même que l'entrée des vco.
J'y connais rien mais il me semble que rajouter un converto lin/expo c'est pas très contraignant.
| |
|
 | |
Haddock Petit lama

Messages : 21 Date d'inscription : 14/08/2012 Age : 53 Localisation : Toulouse
 | Sujet: Re: The Harvestman... en MKII Mar Jan 29 2013, 15:10 | |
| - Yohda a écrit:
- Oui, mais il me semble avoir lu que le clavier sortait en expo, de même que l'entrée des vco.
J'y connais rien mais il me semble que rajouter un converto lin/expo c'est pas très contraignant.
Oui j'ai lu un peu tout et son contraire dans les compte-rendus du NAMM. Franchement je ne sais pas l'impact que ça aurait eu sur la machine. J'imagine que Korg 1) a voulu garder les coûts de développement au minimum et 2) n'a pas voulu donner de grain à moudre aux puristes ("il ont changé X et Y, ça ne sonne pas comme les vrais !"  ). Pas très grave, au pire, le module Harvestman fera l'affaire. J'hésitais déjà sur un offset / attenuverter genre CV-Tools, ça fera d'une pierre deux coups.  | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Mer Fév 06 2013, 15:31 | |
| - bambou a écrit:
- Je sais que le phonogen a un pre-amp sur son entrée audio, est ce que c'est pareil pour le Tyme Sefari ? On peut rentrer directement un signal de niveau line dedans ?
Je me répond au cas où ça intéresserait quelqu'un d'autre : Oui c'est tout à fait possible ! Ici ma première petite jam avec le TS mkII, j'ai pris la première musique de mon iPhone ("IAM - Elle donne son corps avant son nom") que j'ai branché directement dans l'input : [Vous devez être inscrit et connecté pour voir ce lien]Ce module est vraiment...  . | |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Sam Fév 16 2013, 15:13 | |
| [Vous devez être inscrit et connecté pour voir cette image]"Malgorithm mark II is the long-awaited redesign of the world's first voltage-controlled bitcrusher, now available in high-resolution stereo with expanded controls. The bitcrusher is an essential tool in the Digital Modular Synthesist's arsenal. Its primary use is to bring foreign signals into aesthetic compliance with the synthesist's style. This is primarily done through the controlled reduction of two signal parameters, bit depth and sampling rate (labeled "Nyquist"). Bit depth reduction effectively reduces the dynamic range of the signal by eliminating the least significant bits from the audio, destroying the finer details and gradually converting the waveform into a series of "staircases", ultimately arriving at a square wave. Ordinary bitcrushers process the bit depth in integer steps, resulting in a choppy, discrete control respones. Malgorithm features continuous, non-integer bit depth reduction, a modular first. By eliminating the steps from the Bit Depth control sweep, the user may now fully enjoy the full depth of dynamic transformation that this unique process offers, under manual or voltage control. The Sampling Rate control reduces the speed of the digital audio system within Malgorithm to cause a foldover of input frequencies exceeding one-half of the sampling frequency (the Nyquist limit). This sounds like a strange combination of filtering and ring modulation, with bidirectional foldover (forward from zero Hertz) occurring at extreme settings. The extreme spectral manipulation offered by this process responds remarkably well to audio-rate control modulation, offering access to a unique class of new sounds left unexplored by conventional synthesis. After these two processes are complete, the signal optionally passes through a digital waveshaper. Controlled by four brightly illuminated colored buttons, the signal is subjected to four rounds of digital destruction. Fuzzy octave-up weirdness, self-oscillating logic disasters, and harmonically rich waveform crumpling are available in 256 possible combinations. A voltage-controllable wet/dry mix knob is provided to balance this destroyed signal with the clean input sound, and the input gain itself is voltage-controllable to act as an auxiliary VCA, and to achieve dynamic wavefolder effects under certain settings. Under deeper waveshaper settings, the data from the left/right stereo channels crosses over and affects the opposite channel, leading to bizarre effects dependent on the correlation of the two channels. Malgorithm now features full stereo I/O to faciliate insertion into your stereo mix bus." Super intéressant comme module ! Je me demande bien comment peut sonner l'association bitcrusher+waveshaper. | |
|
 | |
MechaSeb Admin
Messages : 4363 Date d'inscription : 15/10/2010 Age : 39
 | Sujet: Re: The Harvestman... en MKII Mar Mai 21 2013, 19:47 | |
| Tadam : [Vous devez être inscrit et connecté pour voir cette image] et du son : _________________ Les compilations synthé-mod Albums & EPs 100% Serge Modular
| |
|
 | |
bambou Lama-mia !

Messages : 597 Date d'inscription : 12/06/2011
 | Sujet: Re: The Harvestman... en MKII Mar Mai 21 2013, 20:46 | |
| | |
|
 | |
dropthedyle Grand lama

Messages : 423 Date d'inscription : 12/09/2012 Localisation : Belle gigue
 | Sujet: Re: The Harvestman... en MKII Mar Mai 21 2013, 22:00 | |
| Le tracking contrôlable en tension, voilà qui me plaît bien, il rejoindra un jour mon mk1 ! | |
|
 | |
Contenu sponsorisé
 | Sujet: Re: The Harvestman... en MKII  | |
| |
|
 | |
| The Harvestman... en MKII | |
|