Vous souhaitez réagir à ce message ? Créez un compte en quelques clics ou connectez-vous pour continuer.

Quelques lamas, sur la cordillère des ondes

Écoutez notre radio

AccueilAccueil  PortailPortail  Dernières imagesDernières images  S'enregistrerS'enregistrer  Connexion  
Le deal à ne pas rater :
PC Portable HP Victus Gaming 16,1″FHD + Souris HP X220 (Via ODR de ...
949.99 € 1199.55 €
Voir le deal


 Fonitronik MH11 ADC Step sequencer

Aller en bas 

Messages : 2594
Date d'inscription : 07/11/2010
Age : 53
Localisation : Fritland

Fonitronik MH11 ADC Step sequencer Empty
MessageSujet: Fonitronik MH11 ADC Step sequencer   Fonitronik MH11 ADC Step sequencer EmptyMer Jan 02 2013, 00:10

Et hop, encore un p'tit séquenceur 8 pas ... "with a twist" ...
La largeur d'impulsion du clock détermine le temps de Gate Bravo
L'entrée P CV permet de programmer l'état binaire de chaque pas de l'ensemble de la séquence avec un CV Bravo 2

[Vous devez être inscrit et connecté pour voir cette image]


The mh11 ADC Pattern Sequencer is an eight-step sequencer for CV, trigger and gate signals. So far it´s kind of like you would expect it to be... BUT:

The rhythmicity of the sequencer can be controlled by the ADC section in an interesting way. The ON / OFF state of each step can be set manually or it can be determined by a value ( 1 or 0) that is decoded by the ADC´s pattern. Sounds complicated but it´s just unusual. See the description below.
technical details

The pulse width of the clock signal at the input determines the gate length of the according step so it makes sense to use e.g. a LFO with pulse width control. The mh11 sequencer can accept clock signals up to audio range making it a graphic oscillator as well. An input for resetting the sequencer back to the first step is available as well. The clock button skips manually to the next step; the reset button resets the sequencer manually.

Besides gates with variable length the sequencer can output triggers at a separate socket.

Now to the ADC section: Each step has a three-position switch which determines if the step is played or muted. In third position a value from the ADC (analog-digital converter) determines if the step is on or off. The ADC converts a 0-5V voltage at the P-CV input into one of 256 possible binary 8-Bit patterns. Each Bit is equivalent to a step of the sequencer and can be either on (1) or off (0). This will produce an sequence like 00101101. The according step set to "ADC" will then read out either a "1" or "0", and thus will be either played or muted. Changing or scaling the input voltage will change the sequence of 1s and 0s and will create nice variations of the rhythmical pattern.

The ADC doesn´t like voltages above 5V so use the attenautor and offset control to adjust the input voltage. The current active step and the current state of the 8 bits are displayed with two LED bars.
inputs and outputs

ADC: Processor CV (P CV) input and P CV output

sequencer: CV output, trigger output, gate output, Reset input, Clock input
measures and weight

3U Eurorack module, 24HP wiede, 46mm deep. Current draw maximum +70mA/-20mA

280.00 €
Revenir en haut Aller en bas
Fonitronik MH11 ADC Step sequencer
Revenir en haut 
Page 1 sur 1
 Sujets similaires
» Fonitronik MH31
» VCP Sequencer fonitronik
» Alimentation Fonitronik TH 555-VCO (T. Henry)
» Beat Step Pro/ Interface Midi to CV
» Killpatrick Audio K2579 // Step Sequencer

Permission de ce forum:Vous ne pouvez pas répondre aux sujets dans ce forum
Synthé-modulaire :: Les systèmes modulaires :: Les modulaires physiques :: Général-
Sauter vers: