Vous souhaitez réagir à ce message ? Créez un compte en quelques clics ou connectez-vous pour continuer.

Quelques lamas, sur la cordillère des ondes

Écoutez notre radio

AccueilAccueil  PortailPortail  S'enregistrerS'enregistrer  Connexion  
Le deal à ne pas rater :
Souris gaming Acer Predator Cestus 350 (sans fil, filaire, 8 boutons) ...
19.99 € 99.99 €
Voir le deal


 Rossum : une histoire de quatre pôles

Aller en bas 

Messages : 4353
Date d'inscription : 15/10/2010
Age : 38

Rossum : une histoire de quatre pôles Empty
MessageSujet: Rossum : une histoire de quatre pôles   Rossum : une histoire de quatre pôles EmptyMar Juin 04 2019, 09:52

Comme beaucoup j'imagine, je trouve les modules Rossum extrêmement intéressant à analyser.
Quoi qu'il en soit, au hasard de lecture des spécifications, je suis tombé sur la genèse de son module Evolution qui est un un filtre multipôle en échelles de transistors type Moog. Son texte, en Anglais, vaut qu'on s'y attarde si le design de filtre et si l'histoire des synthétiseurs en général, vous intéresse un peu :

"The fundamental core of the Rossum Electro-Music EVOLUTION Variable Character Filter is Bob Moog’s famous “ladder” filter, which was described in US Patent 3,475,623. This circuit uses the variation of the Bipolar Junction Transistor’s emitter resistance with current as the voltage variable element in an RC filter. In the Moog implementation, four identical stages each implemented a single real lowpass pole. The Moog 904A module included a “Regeneration” control that created a negative feedback path around the four poles. Since each pole provided 45 degrees of phase shift at its -3dB point, increasing this feedback produced a resonant peak at cutoff. The musical utility of the Moog filter is, of course, famous.

In 1973, E-mu Systems introduced their 1100 submodule, which was the heart of their 2100 lowpass filter module. The 1100 used a Moog ladder as its core element, but I wanted to isolate the innate audio characteristics of the filter ladder from those colorations resulting from the input level-shifters and output amplifier used in the Moog 904A. I also envisioned a DC-coupled design with a cutoff frequency range well beyond 10 octaves, as well as eliminating variations of the height of the resonant peak or oscillation amplitude with frequency control voltage.

I level-shifted the exponential generator to allow the filter signal input to be directly applied to the ladder base. I then designed a completely new output stage for the ladder; this circuit has never (to our knowledge) been used outside my designs. The entire signal path was DC coupled and the resonant feedback path phase compensated. The 1100 was my favorite filter (I liked it more than the SSM2040 I later invented, and kept the 1100 as E-mu’s modular lowpass in preference to a cheaper 2040 design). The operational range of the cutoff frequency was from about 0.1Hz to 25kHz, with stable Q’s throughout.

In launching Rossum Electro-Music, I chose a new implementation of the 1100 filter as the first all-analog module for our Eurorack offering, based on its unique and outstanding audio characteristics. I re-engineered the basic 1100 core using modern available surface-mount components and then added a number of features to the original 1100 design:

Ladder filters self-oscillate, and can be used as VCOs. I was able to design the Rossum Electro EVOLUTION’s frequency control exponential generator to be extremely accurate and temperature stable, rivaling the specifications of the best analog VCOs. I also added a novel temperature compensation circuit for the ladder emitter resistance.

The resonance (“Q”) of the original 1100 was not voltage controlled. I implemented voltage controlled Q using one cell of an SSM2164 VCA (sadly, the original 2164 is no longer produced, so a replica source is needed). Since the SSM2164 is based on my 1979 design of the SSM2010, this is an apt choice. The phase compensation has been maintained, but we added a “Q Compensation” control. The negative feedback resonance path in the 1100, like the Moog 904A, caused the amplitude of signals in the passband to be attenuated as the Q increased, which some users found undesirable. If instead the signal is inserted into the Q VCA, this effect is eliminated. In EVOLUTION, the Q Compensation control allows insertion of the signal with an arbitrary mix into either of these inputs, allowing the ratio of direct to resonant amplitude to be arbitrarily selected.

There is no inherently desirable taper for Q control. In highly resonant, but oscillation-proof filters such as state variable designs, it makes sense to exponentially control Q. But in ladder filters, oscillation is expected, and high Q’s without oscillation are not practically achievable. The Rossum Electro EVOLUTION implements linear control of the Q VCA.

The ladder design, as I implemented it, has no inherent distortion for signals far below the cutoff frequency. The characteristic timbre of the filter comes primarily from distortions of frequencies near and above the cutoff frequency. The degree of distortion depends on the signal amplitude. Consequently, it is sonically interesting to modulate the signal amplitude going into the ladder, and modulate the output signal with the precise inverse gain. This is the function of the Species control. A high voltage into the Species input will cause the filter to distort more audibly.

Because ladder filters produce their resonance by feedback, the relationship of that feedback to the drive VCAs is critical. The Rossum Electro EVOLUTION places the Q feedback within the drive VCAs. This means that the filter’s resonance is unaffected by the Species setting, but that the amplitude of any self-oscillation will be inversely proportional to the Species level. When using the filter as an oscillator, the Species control can be used to amplitude modulate the output. If oscillation is combined with an input signal, the results become even more interesting. Like the Q circuit, SSM 2164 cells are used for the drive VCAs.

With these additions, the preliminary design of EVOLUTION looked pretty complete. Then Marco asked if it would be possible to add voltage controlled slope (those marketing guys are never satisfied). My first take was that this would not be practical, because varying the slope usually involves controlling complex pole pairs, and the ladder comprises only real poles.

Then I realized that I could steer the current around individual ladder stages in an analog manner, controlling the number of poles rather than the slope. A prototype proved this was both practical and audibly pleasing. Since the resonant frequency of a ladder filter is determined by the 180 degree phase shift point, it changes with the number of poles: 60 degrees for three poles, 45 for four, 36 for five, and 30 degrees for six poles. Modulating the number of poles produces a unique “bubbly” sound.

Two more tweaks were needed to complete the circuit. Because the number of poles not only affects the phase shift for resonance, it also changes the amount of feedback required for oscillation, the pole control circuit needs to control the Q VCA in a manner such that the same Q control voltage produces oscillation for each pole setting. And since it’s useful but difficult to tune the initial pole setting to be in the center of the range (exactly steering the current to the desired ladder poles), I added analog controlled LEDs to indicate the activation of the poles.

[Vous devez être inscrit et connecté pour voir ce lien]

Les compilations synthé-mod
Albums & EPs 100% Serge Modular
Revenir en haut Aller en bas
Rossum : une histoire de quatre pôles
Revenir en haut 
Page 1 sur 1
 Sujets similaires
» Intellijel Dr. Octature 4 pôles VCF/LFO
» Nouveautés Eowave : Poles - Sommateur
» [podcast]une histoire de la boucle
» Une histoire des pionniers de la musique électronique
» Noodles pour un 9U [histoire d'un modulaire doepfer]

Permission de ce forum:Vous ne pouvez pas répondre aux sujets dans ce forum
Synthé-modulaire :: Théories et Ressources :: Théories et pratiques des différentes synthèses :: Ressources et documentations-
Sauter vers: